Toyota Valve System,,

VVT-i, or Variable Valve Timing with intelligence, is an automobile variable valve timing technology developed by Toyota, similar in performance to the BMW's VANOS. The Toyota VVT-i system replaces the Toyota VVT offered starting in 24 December 1991 on the 5-valve per cylinder 4A-GE engine. The VVT system is a 2-stage hydraulically controlled cam phasing system. The Toyota motors CEO has been reported to have said, "VVT is the heart of every modern Toyota!"[citation needed] VVT-i, introduced in 1996, varies the timing of the intake valves by adjusting the relationship between the camshaft drive (belt, scissor-gear or chain) and intake camshaft. Engine oil pressure is applied to an actuator to adjust the camshaft position. Adjustments in the overlap time between the exhaust valve closing and intake valve opening result in improved engine efficiency.[1] Variants of the system, including VVTL-i, Dual VVT-i, VVT-iE, and Valvematic, have followed. VVTL-i (Variable Valve Timing and Lift intelligent system) is an enhanced version of VVT-i that can alter valve lift (and duration) as well as valve timing. In the case of the 16 valve 2ZZ-GE, the engine head resembles a typical DOHC design, featuring separate cams for intake and exhaust and featuring two intake and two exhaust valves (four total) per cylinder. Unlike a conventional design, each camshaft has two lobes per cylinder, one optimized for lower rpm operation and one optimized for high rpm operation, with higher lift and longer duration. Each valve pair is controlled by one rocker arm, which is operated by the camshaft. Each rocker arm has a slipper follower mounted to the rocker arm with a spring, allowing the slipper follower to freely move up and down with the high lobe without affecting the rocker arm. When the engine is operating below 6000-7000 rpm (dependent on year, car, and ECU installed), the lower lobe is operating the rocker arm and thus the valves, and the slipper-follower is freewheeling next to the rocker arm. When the engine is operating above the lift engagement point, the ECU activates an oil pressure switch which pushes a sliding pin under the slipper follower on each rocker arm. The rocker arm is now locked into slipper-follower's movements and thus follows the movement of the high rpm cam lobe, and will operate with the high rpm cam profile until the pin is disengaged by the ECU. The lift system is similar in principle to Honda VTEC operation. The system was first used in 2000 Toyota Celica with 2ZZ-GE. Toyota has now ceased production of its VVTL-i engines for most markets, because the engine does not meet Euro IV specifications for emissions. As a result, this engine has been discontinued on some Toyota models, including that of the Corolla T-Sport (Europe), Corolla Sportivo (Australia), Celica, Corolla XRS, Toyota Matrix XRS, and the Pontiac Vibe GT, all of which had the 2ZZ-GE engine fitted. The Lotus Elise continues to offer the 2ZZ-GE and the 1ZZ-FE engine, while the Exige offers the engine with a supercharger. Dual VVT-i 2GR-FSE engine with dual VVT-i The Dual VVT-i system adjusts timing on both intake and exhaust camshafts. It was first introduced in 1998 on the RS200 Altezza's 3S-GE engine. Dual VVT-i is also found in Toyota's new generation V6 engine, the 3.5-liter 2GR-FE first appearing on the 2005 Avalon. This engine can now be found on numerous Toyota and Lexus models. By adjusting the valve timing, engine start and stop occurs almost unnoticeably at minimum compression. Fast heating of the catalytic converter to its light-off temperature is possible, thereby reducing hydrocarbon emissions considerably. Most Toyota engines including the UR engines (V8), GR engines (V6), AR engines (Large I4), and ZR engines (Small I4) now use this technology. VVT-iE VVT-iE (Variable Valve Timing - intelligent by Electric motor) is a version of Dual VVT-i that uses an electrically operated actuator to adjust and maintain intake camshaft timing.[2] The exhaust camshaft timing is still controlled using a hydraulic actuator. This form of variable valve timing technology was developed initially for Lexus vehicles. This system was first introduced on the 2007MY Lexus LS 460 as 1UR engine. The 1UR engine, the first to feature VVT-iE The electric motor in the actuator spins together with the intake camshaft as the engine runs. To maintain camshaft timing, the actuator motor will operate at the same speed as the camshaft. To advance the camshaft timing, the actuator motor will rotate slightly faster than the camshaft speed. To retard camshaft timing, the actuator motor will rotate slightly slower than camshaft speed. The speed difference between the actuator motor and camshaft timing is used to operate a mechanism that varies the camshaft timing. The benefit of the electric actuation is enhanced response and accuracy at low engine speeds and at lower temperatures. Furthermore, it ensures precise positioning of the camshaft for and immediately after engine starting, as well as a greater total range of adjustment. The combination of these factors allows more precise control, resulting in an improvement of both fuel economy, engine output and emissions performance.